You are here

Hobart Airforce 40i Plasma Cutter Inverter 230v 20-40 Amp Output Model #500566

Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566


Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566

Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566
Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566

Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566


Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566




Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566
  Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566



The Hobart AirForce 40i Plasma Cutter is an economical plasma cutting system for all conductive metals. With new XT series torches, new longer life XT consumables, and the newly added Pilot Arc Controller feature, you'll appreciate the enhanced performance. It can cut mild steel up to 7/8in. This portable unit features a lightweight, powerful inverter design and an ergonomic trigger safety, with more efficient air consumption and economically priced consumables. Plasma cutters cut faster and more precisely with a thinner kerf and less slag than cutting with oxy fuel. A smaller heat-affected zone also causes less warping. And you'll never have gas pressure settings, flame tuning, metal preheating, or gas cylinders or refills to worry about. Hobart AirForce 40i Plasma Cutter - Inverter 230V 20-40 Amp Output Model #500566. The Hobart AirForce® 40i Plasma Cutter is an economical plasma cutting system for all conductive metals. Compressor Included: No, Duty Cycle: 50% at 40A, Plasma Gas Flow/Pressure: 4.8 CFM at 90? 120 PSI recommended, Pilot Arc: Yes, Cutting Thickness in. : 5/8 (mild steel, clean cut), Sever Thickness in. : 7/8, Dimensions L x W x H in.

: 14 x 8 x 11, Clamp Cable Length ft. : 12, Volts: 230, Cart: No, Amps: 40, Power Cord ft. Designed for increased comfort with an ergonomic trigger safety, extremely flexible cables, more efficient cooling and economical replacement XT series cutting tips for longer life. Newly added Pilot Arc Controller feature greatly enhances expanded metal cutting, as the auto re-fire technology keeps the torch arc going even when cutting through spaces in the metal where frequent manual restarting is normally required. Prevents abrasive dust and particles from damaging internal components.

Cooling system operates only when needed, reducing power consumption and contaminants drawn into the machine. Power factor correction (PFC) circuitry draws up to 30% less amperage for the same cutting range as compared to the competition. PFC expands operator's work area via extension cord, while minimizing nuisance circuit breaker trips caused by voltage drops.

Line voltage compensation provides peak performance power under variable input voltage conditions (±15%) for steady and cleaner-ending cuts. Internal gas/air filter and regulator controls amount of usage and flow of air or gas. Starts without high frequency, protecting the unit by not interfering with or damaging controls or computers. Diagnostic LED lights for quick troubleshooting of pressure, power and cup situations. Postflow cooling circuit extends life of consumables and torch by cooling them with postflow air after trigger is released.

Compatible with engine-driven welders capable of cutting 3/8? Mild steel when powered by an engine-driven welder with a 240 V generator power outlet of 8 kW or more.
If a PO box address is submitted without a physical address, it may delay your order. We may already have an answer to your question! We reserve the right to correct ad errors and/or omissions.


Pricing and availability is subject to change without notice. The item "Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566" is in sale since Friday, July 26, 2019. This item is in the category "Business & Industrial\CNC, Metalworking & Manufacturing\Welding & Soldering Equipment\Welding Equipment & Accessories\Welders, Cutters & Torches\Plasma Cutters". The seller is "northerntool" and is located in Fort Mill, South Carolina.

This item can be shipped to United States.

  • Brand: Hobart
  • MPN: 500566
  • Manufacturer: Hobart
  • Model Number: 500566
  • Model: 500566


Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566
  Hobart AirForce 40i Plasma Cutter Inverter 230V 20-40 Amp Output Model #500566